Quality & Inspection — AQL Sampling - SAZ
In-line inspection station at the SAZ partner factory
Quality & Inspection

How SAZ controls quality before shipment

SAZ inspects every order at five gates and applies AQL 2.5 sampling in line with ISO 2859-1 at final inspection. Buyers can also book SGS, Bureau Veritas or Intertek for an independent pre-shipment inspection; we release goods only after the report is accepted.

5Inspection Gates
AQL 2.5Major Defects
ISO 2859-1Sampling Standard
100%Carton Check
Sampling tables follow ISO 2859-1; inspection preparation follows the SgT procedure WP-02/4.1. Updated 22 October 2026.
The five gates

Where are the checks carried out?

Each gate has an owner and a written record. A lot that fails a gate does not move to the next one — it is corrected and re-inspected.

GateWhat is checkedRecord
1 · Fabric inColour, weight, shrinkage, defects per roll against the approved swatchRoll inspection sheet
2 · CuttingMarker accuracy, ply count, shade matching per bundleCutting report
3 · In-line sewingStitch density, seam strength, measurement at each operationIn-line check sheet
4 · End of lineMeasurements, symmetry, trims, labelling, hangtag placementFinal check sheet
5 · Pre-shipmentAQL 2.5 sampling, packing, carton marking, assortmentInspection report + photos
AQL sampling

How does AQL 2.5 sampling work?

AQL sampling is a statistical release rule, not a percentage check. You pick an inspection level and an acceptance quality limit; the standard then fixes how many pieces to pull and how many defects are allowed before the lot is rejected. The tables below are the ones our inspectors use, taken from ISO 2859-1.

Step 1 — Pick the code letter from the lot size

General inspection level II is the normal default for garment shipments.
Lot size (pcs)Code letterSample sizeAccept (major)Reject (major)
501 – 1,200J8056
1,201 – 3,200K12578
3,201 – 10,000L2001011
10,001 – 35,000M3151415
35,001 – 150,000N5002122
150,001 – 500,000P → use 5005002122
Worked example from the procedure: an 8,000-piece order at level II gives code letter L, sample size 200, accept 10 / reject 11 for major defects at AQL 2.5, and accept 14 / reject 15 for minor at AQL 4.0.

Step 2 — Follow the arrow on the master table

For very large lots the table can point upward. At 160,000 pieces and level II the code letter is P, but under AQL 2.5 that row is empty with an arrow to sample size 500 — so the inspector uses 500 pieces, not 800. Our inspectors are trained to read the arrow rather than the row label.

Step 3 — Decide how many cartons to open

Pieces must come from different cartons, so the carton count is set first. Three accepted methods:

MethodRuleUse when
Square root√(total cartons) — e.g. 400 cartons → 20 cartonsStandard shipments
Double square root2 × √(total cartons) — e.g. 400 cartons → 40 cartonsMixed sizes or colours
One box per size / colourOpen one carton for every size–colour combinationSmall orders with a large size run — e.g. 3 colours × 5 sizes = 15 cartons

Cartons are then selected at random across the lot — never from the top layer of the pallet, which is where a factory would put its best pieces.

Defects

What counts as critical, major and minor?

Critical — 0 accepted

Safety and legal issues: sharp points, banned azo dyes, wrong fibre content, needle fragments. Any critical defect rejects the lot outright; no sampling allowance applies.

Major — AQL 2.5

Defects a buyer would refuse at full price: broken stitching, wrong measurement beyond tolerance, mismatched shade, incorrect label or size mark.

Minor — AQL 4.0

Cosmetic issues that do not affect sale: slight thread ends, minor pressing marks, tolerable colour variance within the approved range.

Third-party inspection

Can I use my own inspection company?

Yes, and many of our buyers do. We schedule the inspection window, provide the packing list and the sampling units, and hold the shipment until the report is accepted. SGS, Bureau Veritas and Intertek all operate in Shishi and Qianjiang.

Documents we send before inspection

Packing list, size assortment, approved sample reference, trim card, and the internal in-line inspection records for the lot.

What we need from you

The inspection standard you want applied (AQL levels, measurement tolerances), the booking reference, and any client-specific packing or labelling guideline.

References: ISO 2859-1 · SGS · amfori BSCI

Want the full inspection checklist?

We will send the five-gate checklist and the AQL table used on your order before production starts.

Request the checklist →
WhatsApp